Left Hand Slide Shown

• White Metal Clad Finish
• Diamond-Trac ® System
• PowerTron ® Operator
• Five Year Warranty

• Supply where indicated on plans Jamison Mark IV ™ Power Operated Single Leaf Horizontal Sliding Cooler Door, with Diamond-Trac ® System* and PowerTron ® Operator.
• Door leaf to have aluminum extruded structure and to be metal clad with #26 gauge white pre-painted stucco embossed steel front and back. Frame (casings and header) to be constructed of aircraft quality aluminum extrusions with white painted finish.
• Door leaf to be filled with 4" (101.6mm) of Jamifoam non-CFC polyurethane insulation with an R value of 28 at 40°F (4½°C). Frame to be insulated with polystyrene inserts.
• Door leaf to be equipped with low profile pneumatic reversing edge effective full height and full travel of door. Upon contact, door in closing cycle is instantly reversed to open position.
• Adjustable gasket at sides and head of frame and reversing edge cover gasket to be polyester reinforced; door leaves to have sweep type sill gasket.
• Hardware to have protective coating against corrosion. Automatic opening to be provided with two remote control, spring-cushioned, low voltage pull switches.
• Door power to be 208, 240 or 480 volt AC, 60 Hertz (50 Hertz available), three phase. (ARCHITECT TO SPECIFY VOLTAGE.) PowerTron ® power operator to have all gear drive, and all power controls to be fully enclosed in NEMA 1 control boxes. Visible signal light to show when motor is running. Complete door assembly to be ready for connection to power. (ARCHITECT TO DESIGNATE RESPONSIBILITY FOR FIELD WIRING.)

Freezer door specifications to be same as cooler door except for these substitutions and additions:

• Supply where indicated on plans Jamison Mark IV ™ Power Operated Single Leaf Horizontal Sliding Freezer Door with Diamond-Trac ® System* and PowerTron ® Operator.
• Provide Frostop heater cables in top, sides, head, and bottom of door. Complete device to be assembled, ready for connection to 120 volt, 60 Hertz, single phase AC line (other voltages available).

1. Freezer Door is designed for installation in warm room with temperatures +33°F (½°C) and above. If door must be mounted in rooms with temperatures of +32°F (0°C)  and below, contact BMIL International.
2. When cold room temperature is below -20°F (-29°C) and/or the relative humidity is greater than 80% on the warm side, Frostop heater cables should be added to the frame/gasket assembly.
3. If the cold room temperature is below -40°F (-40°C), or if the temperature difference exceeds 90°F (50°C), contact BMIL International.

1. Metal cladding can be stainless steel, stucco aluminum, galvanized, or galvanized steel painted to meet specifications.
2. If stainless steel construction, appropriate hardware components can be chrome plated and/or stainless steel.
3. Padlocking provisions on front or back of door with safety release on opposite side. (Specify which side with locking.) Safety release feature permits door hardware to be released, thus minimizing possibility of personnel being locked in room.
4. 6" (152.4mm) of insulation for freezer door (R value 42).
5. 36" (914.4mm) pedestrian opening with automatic closing.
6. Electric eye or motion detector to protect door from truck passage.
7. Radio control operation from lift truck, 1, 2 or 4 button.
8. Power components for connection to 120 volt AC, 60 Hertz, single phase (other voltages available).
9. Swinging wicket door.
10. Complete NEMA 3, 4, or 12 requirements.
11. Electrical reversing edge.
12. Dual speed operator.
13. Hydraulic operator.
14. M.I.D. requirements.
15. View windows: (contact factory for specific recommendations 12" x 14" (304.8mm x 355.6mm) sealed glass unit).
    a. Cooler Door - 2 layer 1"(25.4mm)  thick
    b. Freezer Door - 3 layer, 1" (25.4mm) thick with 120 V.A.C. heat film (other voltages available).
16. Jambs.
17. Inside trim.
18. Mirror image frame.
19. Floor loop.
20. Push button operation, single or three button (open-close-stop).